Wednesday, May 20, 2009

Instalasi Driver Sound Card Acer eMachines eMD725



instalasi driver souncard pada eMD725 ini kita tidak dapat langsung menjalankan setup.exe yang ada pada CD Driver bawaannya, namun sebelumnya kita harus menginstall MUAA Busdriver (Microsoft Universal Audio Architecture), setelahnya baru dilanjutkan dengan menjalankan file setup.exe untuk driver soundnya.

Download : Microsoft UAA Bus Driver for High Definition Audio

Tuesday, May 19, 2009

Cara Instal laptop baru

Install XP sp2 in notebook with SATA harddisk ?

Always appear command :
“Setup did not find any hard disk drive installed in your computer”

CD WinXP couldnot read the hard disk drive. Firstly, I thought the problem is in Harddisk.
After I check the harddisk, it still couldnot read. Then I Ask Google and I get the Answer.You should check the BIOS setting.

To change SATA Mode : AHCI
become SATA Mode : IDE

Monday, May 11, 2009

Due to an unidentified problem, Windows cannot display Windows Firewall settings

I answer,Really? Here is fine..”, and then I walk to another room, to know whats wrong. “Funny, workgroup Local Area Network (LAN) is fine, internet OK, but why computer in another room couldnot access interne?”.
Internet connection in my office was share with Internet Connection Sharing (ICS) by Windows XP,so one ofcompoter with two LAN Card, one for input internet cable, the other for output to LAN. The logica, if workgroup connection is fine , internet ok, and computer with two lan card is on, so otomatically all of the computer could access internet

After check here and there,finnally I know the problem, Infact Internet Connection Sharing could shut down was caused by trojan and Windows Firewall at computer with two LANcard could not be access. After I clik was appear message “Due to an unidentified problem, Windows cannot display Windows Firewall settings.”

With the helper Google, I start to surfing, and as usual, finnally I found the ways :

1. Download sharedaccess.reg, (only for Windows XP Service Pack 2 or Service Pack 3), then double clik the file for merge to registry windows.

2. Restart computer.

3. Clik Start –> Run, Do the command
CMD /K NETSH FIREWALL RESET

4. Try to open Windows Firewall, if it didnot work.

5. Clik Start –> Run,Do the command

rundll32 setupapi,InstallHinfSection Ndi-Steelhead 132 %windir%\inf\netrass.inf

6. Restart computer.

Sunday, April 19, 2009

Download Antivirus PCMAV 1.3

Antivirus PCMAV 1.3 Release (Download)

New PCMAV 1.3 already released last night. It’s the time to download it. But, i’m still haven’t found where to download it. I Have it now. That’s the usual problem for the first time when PCMEDIA as a developer PCMAV release the update. This program is Freeware but not free. You must buy the pcmedia magazine or PCMild to get PCMAV 1.3 update. That’s more faster than waiting from someone who love sharing program and upload it to rapidshare, 4shared.com or ziddu.

What’s new on this Antivirus PCMAV 1.3?
1. Support or compatible with engine Clamav 0.93 (the new generation of antivirus clamav engine). With this engine, Antivirus PCMAV 1.3 capable to scan 3 times more faster than before. Feel the different.
2. PCMAV RTP works more accurate to block any virus from vbscript type. Included in memory.
3. Special virus cleaner added for virus Amburadul, Euis and Revublik.vbs.
4. 89 local/varian virus added. Total 1.877 Virus.
5. More Improvisation.

Please read the readme file to get more explanation before using it.

Here are the link where you can download it. Free from any virus. I was check it. Except in several antivirus like AVG, etc. PCMAV 1.3 still suspected as virus or trojan. Don’t worry about this.

Download PCMAV 1.3 Here

NEW VIRUS ON Antivirus PCMAV 1.3 (89 Virus)

Akmal.vbs, Akmal.vbs.inf, Allya.vbs, Allya.vbs.inf, Alzheim, Amburadul.A, Amburadul.B, Amburadul.C, Amburadul.D, Amburadul.inf, Architect, Autoit.AR, Autoit.AS, Autoit.AT, Autoit.AU, Autoit.AV, Bluventhexi, Bluventhexi.inf, Bluventhexi.txt, Cetix.D, Cetix.D.html, Cetix.D.inf, Cetix.D.txt, Cyrax-HmteIsta, Danoe.vbs, Danoe.vbs.inf, Emil, Emil.vbs, Euis, Galuh.vbs, Galuh.vbs.inf, Gen.FFE-Master, Gen.FFE-Master.txt, Gen.FFE-Ykcid, Gen.FFE-Ykcid.txt, GerryBlack, GerryBlack.inf, GerryBlack.ini, GerryBlack.txt.A, GerryBlack.txt.B, GerryBlack.txt.C, Hackids, Hackids.bat.A, Hackids.bat.B, Hackids.ini.A, Hackids.ini.B, Hackids.vbs.A, Hackids.vbs.B, Honey, Honey.htm, Honey.ini, IlusiShell.vbs, IlusiShell.vbs.inf, IlusiShell.vbs.txt, Joniezz, Joniezz.inf, KyrEnt.L, MyTob.F, MyTob.F.dll, Nitaku, Nita-Mahadewa.vbs.B, NunukanVixer, NunukanVixer.txt, Paesa.vbs, Paesa.vbs.inf, Payakumbuh.vbs, Payakumbuh.vbs.htm, Payakumbuh.vbs.inf, Postgres, Repvblik.vbs, Scala.vbs, Scala.vbs.inf, SlowAndSilent.vbs, SlowAndSilent.vbs.inf, SmanMadiun, SmanMadiun.bat.A, SmanMadiun.bat.B, SmanMadiun.reg, SmanMadiun.txt, Tuna.vbs.B, WSar.B, Yazzuke.vbs, Yazzuke.vbs.bat.A, Yazzuke.vbs.bat.B, Yazzuke.vbs.inf, Zifoe, Zifoe.txt.A, Zifoe.txt.B

Monday, February 16, 2009

Mikrotik Web Proxy Setting for Transparant proxy

Fo next articel i explain to setting transparant web proxy server

1. first se t web proxy
/ ip web-proxy
set enabled=yes –>> to make ip web proxy enable
set src-address=0.0.0.0 –>> to make source address to access web proxy will allow
set port=8080 –>> to make port for web proxy
set hostname=”proxy.war.net.id” –>> setting for visble hostname web proxy
set transparent-proxy=yes –>> make transparant proxy enable
set parent-proxy=0.0.0.0:0–>> if we used parent proxy x
set cache-administrator=”support@somethink.org” –>> make set administrator info support
set max-object-size=4096KiB –>> maximal object can cacth with the proxy server
set cache-drive=system –>> where drive position that cache wil be saved
set max-cache-size=unlimited –>> maximal harddrive we used for cache
set max-ram-cache-size=unlimited –>> maximal ram we used for cache

2. add nat for redirect port for squid to make transparant

/ip firewall nat add chain=dstnat protocol=tcp dst-port=80 action=redirect to-ports=8080 –>> setting can redirect port 80 to 8080 for proxy server
/ip firewall nat add chain=dstnat protocol=tcp dst-port=3128 action=redirect to-ports=8080 –>> setting can redirect port 3128 to 8080 for proxy server
/ip firewall nat add chain=dstnat protocol=tcp dst-port=8080 action=redirect to-ports=8080 –>> setting can redirect port 8080 to 8080 for proxy server

Thursday, January 29, 2009

Prolink Load Balancing


Hardware

1. PROLINK Load Balancing

2. Mikrotik

3. Proxy

1. Prolink

Config Show


System Configuration Setting
=========================================================================
Firmware: Version : TMH141-A V1023-MB2.4-E
Release Date : Dec 28 2006
Printout Time : SUN JAN 20 01:09:46 2008
Time Zone : GM+08:00
Primary NTP IP: time.nist.gov
Secondary NTP : stdtime.gov.hk
=========================================================
LAN status: IP address : 192.168.1.254
MAC address : 00 :D 0 :D A:00:44:83
Mask : 255.255.255.0
Dhcp status : Disable
Dhcp IP Start : 192.168.1.12 - 192.168.1.20
DNS IP address: 168.95.1.1
=========================================================
DHCP
reserved IP: MAC address IP address
-----------------------------------
=========================================================
WAN status: 1.IP address : 192.168.11.100
Netmask : 255.255.255.0
MAC address : 00.d0.da.00.44.84
Connect To : InterNet
Current status: Enable
Healthy Check : Enable
Type : Static IP
Primary DNS : 192.168.11.254
Secondary DNS : 203.130.193.74
GatewayAddress: 192.168.11.254
Schedule : Disable
---------------------------------------------------------
2.IP address : 192.168.12.100
Netmask : 255.255.255.0
MAC address : 00.d0.da.00.44.85
Connect To : InterNet
Current status: Enable
Healthy Check : Enable
Type : Static IP
Primary DNS : 192.168.12.254
Secondary DNS : 203.130.193.74
GatewayAddress: 192.168.12.254
Schedule : Disable
---------------------------------------------------------
3.IP address : 192.168.13.100
Netmask : 255.255.255.0
MAC address : 00.d0.da.00.44.86
Connect To : InterNet
Current status: Enable
Healthy Check : Enable
Type : Static IP
Primary DNS : 192.168.13.254
Secondary DNS : 203.130.193.74
GatewayAddress: 192.168.13.254
Schedule : Disable
---------------------------------------------------------
4.IP address : 169.254.14.100
Netmask : 255.255.255.0
MAC address : 00.d0.da.00.44.87
Connect To : InterNet
Current status: Disable
Healthy Check : NoDefault
Type : Dynamic IP
Schedule : Disable
=========================================================
Routing setup: Work mode : Basic NAT mode
Static Route :
Network NetMask Gateway Status
-------------------------------------------------------
---------------------------------------------------------
Dynamic Route : Status: Disable
=========================================================
Routing Table: Network NetMask Gateway
---------------------------------------------------
0.0.0.0 0.0.0.0 192.168.13.254
192.168.1.0 255.255.255.0 192.168.1.254
192.168.11.0 255.255.255.0 192.168.11.100
192.168.12.0 255.255.255.0 192.168.12.100
192.168.13.0 255.255.255.0 192.168.13.100
=========================================================
IP Filtering: No. IP address Port Pass/Drop status
-------------------------------------------------------------------------------------------
=========================================================
Remote
IP Filtering: No. IP address Status
---------------------------
=========================================================
DoS Defense: Function Parameter Time of Lock Status
---------------------------------------------------------
Port Scan 1000 5 Enable
TCP SYN Flooding (Wan) 1000 5 Enable
TCP SYN Flooding (Lan) 1000 5 Enable
ICMP Flooding (Wan) 1000 5 Enable
ICMP Flooding (Lan) 1000 5 Enable
UDP Flooding (Wan) 1000 5 Enable
UDP Flooding (Lan) 1000 5 Enable
=========================================================
ALG: Options Status
---------------------------------------------------------
Ipsec Pass Through (Port 500) Disable
PPTP Pass Through (Port 1723) Disable
VOIP Pass Through Disable
=========================================================
Virtual Server: ID Global_Port Local_Port Local_IP_address Status
-----------------------------------------------------
---------------------------------------------------------
Group: StartPort EndPort Local_IP_address TCP/UDP Status
-----------------------------------------------------
=========================================================
Multi-DMZ Host: No. DMZ_Host_IP_address IP_address_from_ISP Status
-----------------------------------------------------
---------------------------------------------------------
Dynamic-IP-DMZ: Wan HOST_IP_address Status
----------------------------------
1 0.0.0.0 Disable
2 0.0.0.0 Disable
3 0.0.0.0 Disable
4 0.0.0.0 Disable
=========================================================
Multi-NAT: No LAN_IP_address NetMask Wan_IP Wan_No
---------------------------------------------------------
=========================================================
Load Balance: Weight Round Robin
Wan 1: 1
Wan 2: 1
Wan 3: 1
Wan 4: 1
=========================================================
Dynamic DNS: Status : Disable
=========================================================
Proxy Server: Status: Disable
=========================================================
Mail Alert : Status: Disable
=========================================================
URL Filtering : Status: Disable
=========================================================
Throughput
Control : Wan DownLoad(kbits/s) UpLoad(kbits/s) Port Usage% Status
---------------------------------------------------------
1. 384 64
---------------------------------------------------------
2. 384 64 80 60 Enable
110 5 Enable
25 5 Enable
21 5 Enable
3128 40 Enable
8080 40 Enable
---------------------------------------------------------
3. 384 64 80 60 Enable
110 5 Enable
25 5 Enable
21 5 Enable
3128 60 Enable
8080 60 Enable
---------------------------------------------------------
4. 0 0
=========================================================
WAN CONTROL:
Special : StartPort EndPort Select-WAN Status
Application ----------------------------------------
0 1000 Wan3 Enable
1000 3127 Wan1 Enable
3128 3128 Wan2 Enable
3129 5049 Wan1 Enable
5050 5061 Wan2 Enable
5062 6660 Wan1 Enable
6661 7000 Wan3 Enable
7001 8079 Wan1 Enable
8080 8080 Wan2 Enable
8081 65176 Wan1 Enable
---------------------------------------------------------
IP binding : No Start-Remote-IP End-Remote-IP StartPort EndPort Select-WAN Status
-------------------------------------------------------------------------
1. 0.0.0.0 0.0.0.0 0 1000 Wan3 Enable
2. 0.0.0.0 0.0.0.0 1000 3127 Wan1 Enable
3. 0.0.0.0 0.0.0.0 3128 3128 Wan2 Enable
4. 0.0.0.0 0.0.0.0 3129 5049 Wan1 Enable
5. 0.0.0.0 0.0.0.0 5050 5061 Wan2 Enable
6. 0.0.0.0 0.0.0.0 5062 6660 Wan1 Enable
7. 0.0.0.0 0.0.0.0 6661 7000 Wan3 Enable
8. 0.0.0.0 0.0.0.0 7001 8079 Wan1 Enable
9. 0.0.0.0 0.0.0.0 8080 8080 Wan2 Enable
10. 0.0.0.0 0.0.0.0 8081 65176 Wan1 Enable
---------------------------------------------------------
Special IP : Start-IP-Address End-IP-Address WAN Status
Assignment --------------------------------------------
=========================================================
QoS IP Control: Local_IP_address DownLoad(kbits) UpLoad(kbits) Wan-Apply Min/Max Status
------------------------------------------------------------------------
=========================================================
Remote Control: Status: Disable
=========================================================
MAC IP binding: Status: Disable
=========================================================================

D-Link Load Balancing



Product Specification

D-Link®, an industry leader in innovative networking solutions, introduces a 4-port router designed for the small business. The DI-LB604 Load Balancing Router embodies the heart of a small business – low overhead and high return on investment. Featuring dual WAN ports and four LAN ports, this router provides consistent network uptime and reliable Ethernet connectivity.

One of the main differentiators the DI-LB604 has from most routers is its dual WAN ports. With the ability to connect up to two Internet connections, the total available bandwidth doubles in capacity and therefore provides a tremendous increase in network efficiency and user productivity. Dual WAN ports also provide a fast-acting failover response mechanism; if one Internet connection goes down, the other automatically takes control to ensure continuous network uptime.

The built-in four-port switch provides computers on the LAN with network connectivity and Internet access. Connect up to four PCs or other networking devices to access company resources and use the Internet. The DI-LB604 is a scalable solution that allows users to add switches as business grows and network needs expand.

The DI-LB604 also features the dual Stateful Packet Inspection (SPI) and Network Address Translation (NAT) firewall with Denial of Service (DoS) attack protection to safeguard your network. This helps keep your network reliable and secure while maximizing the productivity of your network clients. E-mail alerts and a Syslog support ensure that network administrators have the information they need to maintain the network infrastructure. Combine these features with full System Logging, Static DHCP, Access Control List, VPN pass-through, and Network Diagnostic Tools ensures your network is fully protected from malicious attacks and outside intruders.

Setup for the DI-LB604 is straightforward. All the DI-LB604’s settings and configuration can be managed via a web-based utility. Firmware upgrades and automatic notifications are also readily available to ensure the router is always up-to-date.

With businesses becoming increasingly network-dependent, the need to invest in a reliable network solution is crucial. With load balancing capabilities and advanced firewall protection, the D-Link DI-LB604 offers high return on investment for any small business.

Product Specification
WAN

• IEEE 802.3
• IEEE 802.3u
LAN

• 4-port 10/100Mbps RJ-45
• Auto-MDI/MDIX; 802.3/802.3u
Outbound Load Balance & Backup

• Outbound load balance by bytes, packet, & session
• Auto backup connection
Protocols

• Security: NAT, UPAP, CHAP
• Network: TCP/IP, HTTP, DHCP, PPP, UPAP, PPPoE
• Multi-session PPPoE, ICMP, ARP proxy
• Connection: Static IP, Dynamic IP, PPoE, PPTP
VPN

PPTP & IPSec pass through
Firewall
• NAT (Network Address Translation)
• NAPT (Network Address Port Translation)
• DoS (Denial of Service)
• Access control by group
• SPI (Stateful Packet Inspection)
• ICMP filter for WAN
• Ping to Death
• Port Scan
• Packet filter
• URL block
Security
• Admin passwords
• Authentication with UPAP and CHAP for PPPoE
Management
• Management through WAN & LAN port
• HTTP web based management
• Email alert of WAN fail
• Syslog
Application
• Support MSN & Netmeeting
• Support with H.323 VoIP products
• Multi-session PPPoE
• SMTP bind
• SNMP
• UPnP
• NAT status & connection list
• Virtual server
• Multi-DMZ
• MTU changeable for WAN
• Dial-on-demand & Auto-disconnect
• Dynamic DNS
• MAC address clone
• QoS
Firmware upgrade
• HTTP web based download
• TFTP download
Wazranty 1 Year Warranty

www.klinik-printer.com